View TDPXED-57T34P-2301_1323939.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIL-C-81659 Rack and Panel Filter Connectors
TDPX filter connectors are used primarily on commercial and military aircraft for radio and instrumentation equipment and are available in single thru four gang version with standard ARINC shells and polarizing posts. They are intermateable with the standard DPX connectors and available in 9 contact arrangements. Meets applicable portions of MIL-Spec.
TDPX
Note: The TDPX replaces the obsolete DPXJ Series
Performance and Material Specifications
MATERIALS AND FINISHES
Description
Shell
ELECTRICAL
Finish
Contacts Size Available Filter Catalog Reference Voltage Rating Current Rating (Amp DC) Insulation Resistance, 2 min. electrification time max. at 25C and 100 VDC 5 amp 20 & 22 Low Freq. L Mid Freq. M 20, 16 & 22 Std. Freq. T High Freq. H 16 Low Freq. L
Material
Aluminum alloy
Cadmium plate (yellow chromate)
Contacts Insulator Interfacial and Peripheral Seals Ground Plane Polarizing Posts
Copper alloy High grade plastic Neoprene rubber
Gold over suitable underplate none none
200 VDC - 120 VAC rms 400 Hz 7.5 amp - size #20, 20 amp - size #16 5,000 megohms minimum @ 100 VDC 300 VDC 32,000 45,000 Freq. MHz 8,000 12,000 500 VDC 2,300 5,000 Attenuation (dB) 2 min. 15 min. 20 min. 35 min. 60 min. 65 min. Pi 2 min. 5 min. 20 min. 55 min. 60 min. Pi 2 min. 12 min. 50 min. 55 min. Pi 2 min. 30 min. 50 min. Pi 2 min. 15 min. 20 min. 35 min. 50 min. 50 min. Pi 850 1,300 500 VDC 32,000 45,000 20 amp
Beryllium copper Stainless steel
Silver plate Passivate
DWV, sea level, with 500 microamps max. charge/discharge current Capacitance at 1 KHz, 0.1 V rms picofarads
Attenuation per MIL-STD-220 at 25C with no applied voltage or current.
0.1 1 2 10 100 500 to 10,000
Filter Type =Check Factory for availability of Size 22 "T" filters.
How to Order - Single Gang
T DPX E B 57 L 34 P 00 01
FILTER SERIES INDICATOR SERIES PREFIX ENVIRONMENTAL SHELL STYLE CONTACT ARRANGEMENT CAPACITANCE INDICATOR SHELL TYPE CONTACT TYPE MODIFICATION POLARIZING POSITION FILTER SERIES INDICATOR T - Transverse Monolith SERIES PREFIX Single gang DPX ENVIRONMENTAL E - For interfacial (pin) Delete for standard SHELL STYLE B - Polarized ARINC B shell (preferred) D - DPXA flange (less polarizing posts) CONTACT ARRANGEMENT See page 318. CAPACITANCE INDICATOR L - Low Frequency M - Mid Frequency T - Standard Frequency Note: Use of "T" omitted in past nomenclature. H - High Frequency N - No filters this gang. Standard DPX insert assembly. SHELL TYPE 33 - Male (plug) 34 - Female (receptacle) CONTACT TYPE P-Pin; S-Socket MODIFICATION TDPXD None TDPXB 03 - Mounting holes countersunk 100 to .230 (5.84) dia. 23 - With floating eyelets. Consult factory. POLARIZING POSITION See pages 67 - 68.
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
316
MIL-C-81659 Rack and Panel Filter Connectors
How to Order - Multiple Gang
T DPX 4 E 57 T P 57 N P 57 M P 57 L P -
TDPX
34
-
00
01
FILTER SERIES INDICATOR SERIES PREFIX GANGS IN SHELL ENVIRONMENTAL CONTACT ARRANGEMENT (Side A) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side B) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side C) FILTER TYPE CONTACT TYPE CONTACT ARRANGEMENT (Side D) CAPACITANCE INDICATOR CONTACT TYPE SHELL TYPE MODIFICATION NUMBER POLARIZING POSITION FILTER SERIES INDICATOR T - Transverse Monolith SERIES PREFIX DPX - DPX series with solder termination. GANGS IN SHELL 2, 3, and 4 gang ENVIRONMENTAL E - For interfacial (pin) Delete for standard. CONTACT ARRANGEMENT See page 31 for applicable arrangements. Please specify each arrangement number as indicated in ordering nomenclature for 2, 3, or 4 gang. CAPACITANCD INDICATOR (Each gang, as desired)* L - Low Frequency M - Mid Frequency T - Standard Frequency Note: Use of "T" omitted in past nomenclature H - High Frequency N - No filter this gang. Standard DPX insert assembly. CONTACT TYPE P for pin; S for socket. Designation follows each arrangement as ordered for 2, 3, or 4 gang versions. (Printed circuit contact/termiation is available. Consult factory for specifications.) SHELL TYPE 33B for male (ARINC B) 34B for female (ARINC B) 33 for male 34 for female Note: ARINC B specified for DPX2 only. POLARIZING POSITION (see pages 67-68) The last two digits in the four-digit dash number refer to the polarizing post position. When the last two digits are omitted, the polarizing posts will be assembled in position 01, but the position number is not stamped on the connector. This allows the customer to position the posts themselves nd then stamp the appropriate number on the shell. If the last two digits are 00, the polarizing posts are deleted. MODIFICATION NUMBERS - 0001 indicates standard design for all styles. TDPX2-33B: - 0301 Mounting holes .120 dia. Countersunk 100 to .230 dia.
TDPX2-34:
- 0101 TDPX3-34:
With #4-40 clinch nuts in mounting holes. With 6 #4-40 clunch nuts in mounting holes. With 10 #4-40 clinch nuts in mounting holes.
- 0101 TDPX4-34:
- 0101 -
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
317
MIL-C-81659 Rack and Panel Filter Connectors
Contact Arrangements
6 12 A2 16 20 24 30 23 29 28 27 5 11 15 19 4 10 9 14 18 3 8 13 17 22 26 21 25 2 7 A1 1
TDPX
6 13 19 26 25 12
5 11 18 24
4 10 17 23
3 9 16 22
2 8 15 21
1 7 14 20
Arrangement No. No. of Contacts & Wire Size
32C2 30 #20, 2 coax
26 26 #16
6 14 23 31 40 39 22 30 13 21
5 12 20 29 38 37
4 11 19 28 36
3 10 18 27 35
2 9 17 26 34
1 8 16 25 33 24 32 7
19
7 13
6 12 18 24 23 29 39
5 11 17 22 28 38 37
4 10
3 9
2 8 14
1
7 15
A1
6 14 13
5 12 21 31
4 11
3 10
2 9 18 28 38
1 8 17 27 37 16 26 36
16 21 27
15 20
15
31 30 26 36 35 25 34 33 32
25 35 45
24 23 34 44 33 43
22 32
20 19 30 40 29 39
42 41
Arrangement No. No. of Contacts & Wire Size
40 40 #20
40C1 39 #20, 1 coax
45 45 #20
9 19 18 28 38 47 57
8 17
7 16 26 36 35 45
6 15 25 34
5 14
4 13
3 12 22 32 31
2 11 21 30
12
1
7 6 5 13 4 12 3 2 11 10 1 9 8
1 13 26 40 53 67 80 94
10 20 29
17 16 15 14 29 28 27 42 41 40 54 53
25 39 52 66 79 93 106
27
24 23 33
26 25 24 23 22
21 20 19 18 33 32 31 30
37 46
39 38 37 36 35 34
44 54
43 53
42 41 52
40
39 48
52 51 50 49 48 47
46 45 44 43 59 58 57 56 55
56
55
51 50 49
67 66 65 64 63 62 61 60
Arrangement No. No. of Contacts & Wire Size
57 57 #20
67 64 #20, 3 #16
106* 106 #22
NOTE: Consult factory for part numbers for special combinations of filter, group contacts and power contacts, and for availability of filter socket contacts, for each contact arrangement.
Contacts - Pin and Socket
Standard Contact Terminations Finish: Gold plate per MIL-G-45204, Type 1, Class 1, over nickel plate per QQ-N-290.
A
C DIA.
B DIA. Pin/Solder Pot Socket/Printed Circuit .025 (0.64) DIA + EXTENSION MAX Pin/Printed Circuit
.025 (0.64) DIA + EXTENSION MAX
Contact Size 20 16 22
A .125 (3.18) .110 (2.79) .170 (4.32) .150 (3.81) .115 (2.92) .095 (2.41)
B .065 (1.65) .061 (1.55) .103 (2.62) .097 (2.46) .005 (1.40) .051 (1.30)
C .048 (1.22) .043 (1.09) .078 (1.98) .069 (1.75) .040 (1.02) .036 (0.91)
PC Tail Extension Max. .200 (5.08), .285 (7.24), .375 (9.52) .200 (5.08), .285 (7.24), .375 (9.52) .200 (5.08), .285 (7.24), .375 (9.52)
Polarization - Page 34.
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
318
MIL-C-81659 Rack and Panel Filter Connectors
Single Gang
TDPXB
TDPX
2.000 (50.80) Two Holes .120 (3.05) Dia. Mfg. Ref. Only 1.612 + .005 _ (4.94 + 0.13) _ .766 (19.46) .720 + .005 _ (18.29 + 0.13) _ L* .125 (3.18) 135 typ. .225 (5.72) Max. Two Holes .120 (3.05) Dia. for Mfg. Ref. Only
2.000 (50.80) 1.750 + .005 _ (44.45 + 0.13) _ .120 (3.05) Dia. 4 Mfg. Holes .060 (1.52) .720 + .005 _ (18.26 + 0.13) _ .125 (3.18) L*
.225 (5.72) Max.
.988 + .005 _ (25.09 + 0.13) _ 1.720 + .005 _ (43.69 + 0.13) _
2.012 (51.10)
1.405 (35.69)
2.047 (51.99)
+
.120 (3.05) Dia. and C' Sunk 82x.230 (5.84) Dia. 4 Holes .719 + .005 _ (18.26 + 0.13) _ 3 Polarizing Posts .719 + .005 _ (18.26 + 0.13) _
+
1.720 + .005 _ (43.45 + 0.13) _
3 Polarizing Posts
1.437 + .005 _ (36.50 + 0.13) _
1.437 + .005 _ (36.50 + 0.13) _
33 ARINC B Shell
34 ARINC B Shell
* This length varies between the limits of 1.750 (44.45) and 1.437 (36.25) depending on the particular construction as determined by contact arrangement.
TDPXD
2.312 (58.72) 1.750 + 0.16 _ (44.45 + 0.15) _ 1.125 + .015 _ (28.58 + 0.38) _ 1.754 (44.55) Max.
.120 (3.05) Dia. 4 Mfg. Holes
.225 (5.72) Max. solder pot extentsion
.750 + .005 _ (19.05 + 0.13) _
.188 (4.78)R Typ.
2.062 + .006 _ (52.37 + 0.15) _
.125 (3.18)R Typ.
.344 (8.74)
.125 (3.18)
DPXA Shell Style
Two Gang
TDPX2
.120 (3.05) Dia. anc C' Sunk 82x.230 (5.84) Dia. 4 Holes
TOP
L* Two Holes .120 (3.05) Dia. for Mfg Ref. Only .766 (19.46) .125 (3.18)
Two Holes .120 (3.05) Dia. for Mfg. Ref. Only .225 (5.72) Max. 3 Polarizing Posts 2.468 + .005 _ (62.69 + 0.13) _
1.750 + .005 _ .188 (4.78) R Typ.
TOP
L* .060 (1.52) .125 (3.18) .225 (5.72) Max.
2.783 + .005 _ (70.69 + 0.13) _ 3 Polarizing Posts 3.110 2.331 + .005 _ (59.21 + 0.13) _
3.075 (78.11)
+
+
2.783 + .005 _ (70.69 + 0.13) _
.719 + .005 _ (18.26 + 0.13) _ 1.437 + .005 _ (36.50 + 0.13) _
.720 + .005 _ (18.29 + .013) _ .188 (4.78)R 2.00 (50.80) 1.612 + .005 _ (40.94 + 0.13) _
.988 + .005 _ (25.10 + 0.13) _
.719 + .005 _ (18.26 + 0.13) _ 1.437 + .005 _ (36.50 + 0.13) _ 2.000 (50.80)
.720 + .005 _ (18.29 + 0.13) _ 4 Mfg. Holes .120 (3.05) Dia. for #4-40 Screws
33B ARINC B Shell
34B ARINC B Shell
* This length varies between the limits of 1.750 (44.45) and 1.437 (36.25) depending on the particular construction as determined by contact arrangement.
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
319
MIL-C-81659 Rack and Panel Filter Connectors
Three Gang
TDPX3
TDPX
L* 2.000 (50.80) 1.612 (40.94) .766 (19.46) .225 (5-72) Max. 2.000 (50.80) 1.750 (44.45) L* .060 (1.52) .225 (5.72) Max. solder pot extension
4.354 (110.59) 4.026 (102.26)
4.318 (109.68) 4.026 (102.26)
3.711 (94.26)
.988 (25.10)
.282
.718 (18.24) 1.437 (36.50)
.180 (4.57)R. Typ.
.125 (3.18)
.282 (7.16)
.718 (18.24) 1.437 (36.50)
6 MTG HOLES .120 (3.05) DIA.
.125 (3.18)
33 Shell * This length varies between the limits of 1.750 an 1.437 depending upon particular construction as determined by contact arrangement.
34 Shell
Four Gang
TDPX4 L* 3.860 (98.04) 1.612 (40.94) .766 (19.46) .225 (5.72) Max.
3.860 (98.04) 3.610 (91.69) .060 (1.52)
L* .225 (5.72) Max.
3.110 (78.99)
2.783 (70.69) 3.110 (78.99) .988 (25.10) 2.783 (70.69)
2.468 (62.69)
.930 (23.62) 1.648 (41.86)
.180 (457(R Typ. .282 (7.16) 33 Shell
.125 (3.18)
10 Mtg. Holes .120 (3.05) Dia.
.930 (23.62) 1.648 (41.86) 34 Shell
.282 (7.16)
.125 (3.18)
* This length varies between the limits of 44.45 an 36.25 depending upon particular construction as determined by contact arrangement.
Panel Cutouts - Pages 69-71.
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
320
ARINC 600 Rack and Panel Filter Connectors
TBKAD/E connectors represent a major milestone in presenting a new rack and panel connector for support of the air transportation market. Several important design concerns have benn addressed and solved in this series. High mating forces of pluggable modules in a rack have been reduced by approximately two-thirds. Filter adaptations include either single module of tandem (dual) module with crimp piggyback rear release contacts. In the ARINC 600 connector series, size 22 contacts are the only size that utilize the Pos-Align Connector Construction feature. The hooded socket extends from its receptacle insulator in the filter design.
TBKAD
Low insertion force contacts. Non-environmental versions. Polarizing posts that are removable from the mating face. Field replaceable inserts for size 22 and power contacts. Field replaceable filter modules with size 22 contacts. Up to 800 size 22 contacts in one connector. Crimp piggy back and pi contacts for filter module. Uses standard DPX crimp, insertion/extraction tooling. Waveguide connections available.
How to Order
T BKA D 2 100 M 4 80 81 *
FILTER SERIES INDICATOR ** CONNECTOR SERIES CLASS SHELL SIZE CONNECTOR LAYOUT DESCRIPTION CAPACITANCE INDICATOR SHELL STYLE CONNECTOR MOUNTING MODIFIER POLARIZING POSITION SPECIAL MODIFIER FILTER SERIES INDICATOR T - Transverse Monolith CONNECTOR SERIES BKA (Per ARINC 600) * * Consult factory for availability. CLASS D - Non-environmental (rear release, crimp contacts) CONNECTOR LAYOUT DESCRIPTION Three digit number contained within the shell layout indicates total number of contacts available
Connector Shell Layout Size -060 -A060 -120 -100 -300 -400 -600 -800 1 1 1 2 2 2 3 3 Shell Cavity Identification A 60 60 150 150 150 150 B 60 60 150 150 150 150 C 100 100 100 150 150 150 150 100 Connector Size 1 2 3 # of Clinch Nuts Receptacle 4 6 10 D E F
SHELL SIZE 1-Max. contact capacity - 125 2-Max. contact capacity - 400 3-Max. contact capacity - 800 CAPACITANCE INDICATOR L - 32,000-45,000 PF M - 8,000-12,000 PF T - 3,300-5,000 PF H -850-1,300 PF SHELL STYLE 3-Plug (rack side) consult factory 4-Receptacle (box side) CONNECTOR MOUNTING MODIFIER 00-Standard design .148 dia. holes 01-With #6-32 ESMA (#12 NCFMA2-62) clinch nuts
02-Size 1 receptacle only - less 3 printed circuit board mounting lugs 03-With #4-40 ESMA (#22 NCFMA2-40) clinch nuts
Connector Size 1 2 3 # of Clinch Nuts Receptacle 4 6 10
08-Size 2 and 3 receptacle only-with #4-40 ESMA (#22 NCFMA2-40) clinch nuts (all mounting holes) 09-Size 2 and 3 receptacle only-with #6-32 ESMA (#12 NCFMA2062) clinch nuts (all mounting holes) 23-with floating eyelets (.048 min. radial float) 4 corner holes per connector Consult factory if other modifications are required. POLARIZING POSITION 01 thru 99 (per ARINC 600) Blank-Polarizing posts or keys not installed but supplied with connector SPECIAL MODIFIER Consult factory
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
321
ARINC 600 Rack and Panel Filter Connectors
Performance and Material Specifications
MATERIALS AND FINISHES
Material Shell Finish
TBKAD
BKAD
Aluminum Alloy Clear chromate over cadmium
SPECIFICATIONS
QQ-A-591/A380 QQ-P-416
Insulator
Material Material
Thermoplastic Copper alloy Gold over nickel Crimp Coper alloy Sliver
N/A AA-C-533
Contacts
Finish Termination Material
N/A
Ground Spring
Finish
ELECTRICAL DATA (Size #16, Size #20 and Size #22)
Filter Description Catalog Indicator Voltage Rating Current Rating (amp DC) Insulation Resistance, 2 min. electrification time max. at 25C DWV, sea level, with 500 microamps max. charge/discharge Capacitance at 1 KHz 0.1 V rms Picofarads Freq. MHz Attenuation per MIL-STD-220 @ 25C with no applied voltage or current 0.1 1.0 2 10 100 500 to 1000 Filter Type/Construction Consult factory for higher or mixed attenuation values and higher voltage ratings. 2 min. 10 min. 16 min. 40 min. 60 min. 65 min. Pi 2 min. 7 min. 18 min. 55 min. 60 min. Pi 2 min. 8 min. 45 min. 55 min. Pi 2 min. 30 min. 45 min. Pi Low Freq. L Mid Freq. M Std Freq. T High Freq. H
200 VDC-120 VAC rms 400 Hz 15 amp size 16, 7.5 size 20, 5.0 amp size 22 5,000 megohms min. @ 100 VDC 300V DC size 22 500V DC size 16 & 20 32000 45000 500VDC 8000 12000 500VDC 3300 5000 500VDC 850 1300
Contact Arrangements (Receptacle-Engaging Face Shown)
Size 1 Sizes 2 & 3
60 60 #22 SHELL CAVITY A or B NOT TOOLED
150 150 #22 SHELL CAVITY A, B, D, or E
100 100 #22 SHELL CAVITY C or F NOT TOOLED
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
322
ARINC 600 Rack and Panel Filter Connectors
Size 1 Receptacle
Filter Module
TBKAD
BKAE SERIES 1.531 (38.89) MAX
.205 (5.21)* .195 (4.95)
BKAD/BKAF SERIES 1.221 (31.01) MAX .130 (3.30) .120 (3.05)
1.010 (25.65) .990 (25.15) .655 (16.64) .645 (16.38) .148 + .003 (3.76 + 0.08)DIA _ _ 4 PLCS MTG HOLES
.125 (3.18)* .105 (2.67)
A
5.465 (138.81) 5.455 (138.56)
A
.135 (3.43)* .115 (2.92) 3.825 (97.16) 3.815 (96.90)
7.455 MAX (189.36)
B
6.355 (161.42) 6.345 (161.16)
6.627 (168.33) 6.607 (167.82) B
2.059 (52.30) 2.049 (52.04)
1.313 (33.35) 1.303 (33.10)
C
C
.135 (3.43) .125 (3.18) .810 (20.57) .800 (20.32) .575 (14.60) .565 (14.35) .705 (17.91) .695 (17.65)
BKAD/BKAF SERIES 1.317 (33.45) MAX BKAE SERIES 1.670 (42.42)
.188 (4.78) .184 (4.67)
Retainer Plate * This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.
Size 2 Receptacle
FILTER MODULE BKAE SERIES 1.531 (38.89) MAX BKAD/BKAF SERIES 1.221 (31.01)MAX 130 (3.30 .120 (3.05)
1.810 (45.97) 1.790 (45.47) 1.431 (36.35) 1.421 (36.09) .655 (16.64) .645 (16.38) .148 + .003 (3.76 + 0.08) DIA. _ _ 10 PLCS MTG HOLES
260 (6.60)* 250 (6.35) .070 (1.78)* .050 (1.27)
5.335 (136.02) 5.345 (135.76)
A
A
.135 (3.43)* .115 (2.92) 3.770 (95.76) 3.760 (95.50)
B
6.975 MAX (177.16)
B
6.360 (161.54) 6.340 (161.04)
2.004 (50.90) 1.994 (50.65) 1.258 (31.95) 1.248 (31.70)
6.627 (168.33) 6.607 (167.82) C
C
2.135 (54.23) 2.125 (53.98)
.870 (22.10) .850 (21.59)
.168 (4.27) .158 (4.01) 1.415 (35.94) 1.405 (35.69)
BKAD/BKAF SERIES 1.317 (33.45) BKAE SERIES 1.670 (42.42)
.188 (4.78) .184 (4.67)
Retainer Plate * This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
323
ARINC 600 Rack and Panel Filter Connectors
Size 3 Receptacle
TBKAD
FILTER MODULE BKAE SERIES 1.531 (38.89) MAX
3.275 (83.18) 3.245 (82.42) 2.891 (73.43) 2.881 (73.18) 1.955 (49.66) 1.945 (49.40) .148 .003 (3.76 + 0.08) DIA. _ 14 PLCS MTG HOLES
260 (6.60)* 250 (6.35)
BKAD/BKAF SERIES 1.221 (31.01)MAX 130 (3.30 .120 (3.05)
.655 (16.64) .645 (16.38)
5.335 (136.02) 5.345 (135.76)
.070 (1.78)* .050 (1.27)
.135 (3.43)* .115 (2.92)
6.975 MAX (177.16)
6.355 (161.42) 6.345 (161.16)
6.627 (168.33) 6.607 (167.82)
2.004 (50.90) 1.994 (50.65) 1.258 (31.95) 1.248 (31.70)
2.135 (54.23) 2.125 (53.98)
3.770 (95.76) 3.760 (95.50)
.865 (21.97) .855 (21.72)
.168 (4.27) .158 (4.01) 1.440 (36.58) 1.430 (36.32) 2.875 (73.02) 2.865 (72.77)
1.252 (31.80) 1.242 (31.55) 2.712 (68.88) 2.702 (68.63)
BKAD/BKAF SERIES 1.317 (33.45) BKAE SERIES 1.670 (42.42)
.188 (4.78) .184 (4.67)
Retainer Plate
* This dimension indicates distance from centerline of retaining screw to the centerline of first contact cavity.
Panel Cutouts
1.530 (38.86) MIN 3.000 (76.20) MIN .191 (4.85) .189 (4.80) 3 PL 2.889 (73.38) 2.883 (73.23) 3 PL .287 R MAX (7.29) 8 PL
.240 (6.10)MAX
.191 (4.85) 2 PL .189 (4.80)
191 (4.85) 189 (4.80) 2 PL
.030 R (.76) MAX 2 PL
240 (6.10) MAX 6.353 (161.37) 6.347 (161.21) 1.429 (36.30) 1.423 (36.14) 3 PL
030 R (.76) MAX 2 PL .180 (4.57) .166 D (4.22) 10 PL .260 (6.60) .230 (5.84) 2 PL .120 R (3.05) MAX 4 PL
240 MAX. (6.10) .030 R MAX (.76) 2 PL .120 R MAX (3.05) 4 PL .180 (4.57) .166 (4.22) 14 PL D
6.870 (174.50) MIN 6.353 (161.37) 6.347 (161.21) .287 R (7.29) MAX 4 PL .240 (6.10) MAX
6.870 (174.50) MIN
.960 (24.38) .930 (23.62) 2 PL
6.870 (174.50) MIN.
.120 R (3.05) MAX 4 PL
2.780 (70.61) MAX
2.200 (55.88) MIN
2.133 (54.18) 2.127 (54.03)
2.780 (70.61) MAX 2.133 (54.18) 2.127 (54.03)
2.20 (55.88) MIN
.180 (4.57) .166 (4.22) D 4 PL 3.65 (9.27) 3.55 (9.02) .653 (16.59) .647 (16.43)
.365 (9.27) .355 (9.02)
.240 MAX (6.10)
.287 R (7.29) MAX 8 PL .653 (16.59) .647 (16.43) 2 PLC
.365 (9.27) .355 (9.02)
.240 (6.10) MAX
.930 (23.62) MIN
1.953 (49.61) 2 PL 1.947 (49.45)
.653 (16.59) 2 PL .647 (16.43)
Size 1 Receptacle
Size 2 Receptacle
Size 3 Receptacle
Dimensions are shown in inches (millimeters). Dimensions subject to change.
www.ittcannon.com
324

▲Up To Search▲

Price & Availability of TDPXED-57T34P-2301

	To Download TDPXED-57T34P-2301 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .